101

Sampling

P1 P2 P3 P4 P5 P8

For example if you change the sample address by one, the

vertical line in the LCD that indicates the sample address

will move in steps of one pixel.) In the vertical axis, you can

zoom-in from 1X (full range display) to 512X (or 1024X in

the case of stereo display).

Zoom-In/zoom-out will occur starting at the “Edit Range

Start” or “Edit Range End” points you specify. (If a different

parameter is selected when you zoom-in or -out, the zoom-

in/out will be based on the last-selected point. If you re-

select the “Edit Range Start” or “Edit Range End” points

when the display is zoomed in or out, the display range will

be adjusted so as to show the selected point.)

If the zoom ratio is low (1X or less), the “sample wave-

form display” may differ slightly from the displayed

waveform before and after waveform editing, but this

does not affect the playback sound. If this occurs, rais-

ing the zoom ratio will make the display accurate.

▼ 1–1: Page Menu Command

When using the page menu commands “Truncate”–

“Volume Ramp” to edit the waveform data of a sample,

ﬁrst use “Edit Range Start” and “Edit Range End” to

select the range that will be edited, and then choose and

execute the desired page menu command.

There is no compare function that lets you return the

edited result to the state before editing. If you wish to

preserve the unedited sample, uncheck the “Over-

write”

item in the dialog box of each page menu com-

mand before you execute.

To edit the “Start” (start address) location at which the

sample data (waveform data) will begin playing, the

“LoopS” (loop start address), or “End” (end address),

use P2: Loop Edit. If the above parameters are located

within an area of sample addresses that are deleted or

moved by your editing, they will automatically be

moved.

Remarks on editing stereo samples

• For stereo samples, the L channel and R channel samples

are edited simultaneously. If you wish to edit only the L

channel or R channel, select a mono multisample, and

select either the L channel or R channel sample for

editing.

• For stereo samples, the display will indicate “Save to

No.(L)” and “(R).” These respectively specify the

writing-destination sample numbers for the L and R

channels.

• If you “Copy” a mono sample into the buffer, and then

“Insert,” “Mix,” or “Paste” it to a stereo sample, the data

will be inserted, mixed, or pasted into both the L and R

sides. (The result is that a stereo sample will be created.)

If you “Copy” a stereo sample into the buffer, and then

“Insert,” “Mix,” or “Paste” it to a mono sample, the L-

and R-side data in the buffer will be mixed to mono, and

then inserted, mixed, or pasted. (The result is that a mono

sample will be created.)

You can also use these commands if you wish to mono-

mix a stereo sample and use it as a mono sample. How-

ever, be aware that once a sample has been mixed to

mono, it is no longer possible to return it to a stereo sam-

ple.

: About “Overwrite”

When “Overwrite” is unchecked: When the command is

executed, the edited sample will be saved in a different sam-

ple number. The unedited sample will remain without

change.

When “Overwrite” is checked: When the command is exe-

cuted, the edited sample will be overwritten onto the origi-

nal sample (number). The original sample will be modiﬁed.

Normally, you will leave “Save to No.” at its default

setting, and execute without checking “Overwrite.”

When you execute, both the data before and after edit-

ing will be preserved, and the sample number of the

edited data will be assigned as the sample of that index.

Loop Start Address “LoopS” and End Address “End”

(2–1c) must be located at least eight addresses apart. If

as a result of executing “Truncate” (1–1A), “Cut” (1–

1B), or “Rate Convert” (1–1K), the Loop Start Address

and End Address would be separated by less than eight

addresses, the display will indicate “Sample length is

shorter than minimum.” Please set the “Edit Range

Start” and “Edit Range End” appropriately.

1–1A: Truncate

This command deletes unwanted data that lies beyond the

“Edit Range Start” and “Edit Range End.” Use this com-

mand when you wish to delete silence at the beginning or

end of the waveform data.

If you wish to delete unneeded (unplayed) sample data

after setting the Start Address “Start,” Loop Start

Address “LoopS” and End Address “End” (2–1c), use

the “Truncate” page menu command found in P2: Loop

Edit.

1 Use “Sample Select” (1–1b) to select the sample that you

wish to edit, and use “Edit Range Start” and “Edit Range

End” to specify the editing range.

You can press the SAMPLING [START/STOP] key to

hear the portion that will be left by the “Truncate” com-

mand.

2 Select “Truncate” to access the dialog box.

3 The editing range will be shown in Range “Start” and

“End.”

4 Use the radio buttons to select the portion that will be

deleted.

Front & End: The sample data that lies before the “Edit

Range Start” and after the “Edit Range End” will be

deleted.

Front: The sample data that lies before the “Edit Range

Start” will be deleted.

1–1A

1–1B

1–1C

1–1D

1–1E

1–1G

1–1H

1–1I

1–1J

1–1F

1–1K

1–1L

1 2 ... 107 108 109 110 111 112 113 114 115 116 117 ... 321 322

Komentáře k této Příručce

Žádné komentáře

JVC CS-V6 SERIES CS-V6936 manuály

Uživatelské manuály a uživatelské příručky pro Reproduktory do auta JVC CS-V6 SERIES CS-V6936.
Poskytujeme 1 manuály pdf JVC CS-V6 SERIES CS-V6936 ke stažení zdarma podle typů dokumentů: Uživatelský manuál

Modely	Typ Dokumentu
CS-FX502	Uživatelský manuál JVC CS-FX502 User Manual, 2 stránky
GET0570-002B	Uživatelský manuál JVC GET0570-002B User Manual, 4 stránky
GET0075-001A	Uživatelský manuál JVC GET0075-001A User Manual, 54 stránky
GET0642-002A	Uživatelský manuál JVC GET0642-002A User Manual, 2 stránky
EXAD LVT1373-001A	Uživatelský manuál JVC EXAD LVT1373-001A User Manual, 58 stránky
GET0139-001A	Uživatelský manuál JVC GET0139-001A User Manual, 33 stránky
KD-AR7000	Uživatelský manuál JVC KD-AR7000 User Manual, 153 stránky
GET0260-003B	Uživatelský manuál JVC GET0260-003B User Manual, 64 stránky
KD-DV6102	Uživatelský manuál JVC KD-DV6102 User Manual, 68 stránky
KD-G720	Uživatelský manuál JVC KD-G720 User Manual, 256 stránky
CH-X350/X300	Uživatelský manuál JVC CH-X350/X300 User Manual, 6 stránky
LVT1055-001A	Uživatelský manuál JVC LVT1055-001A User Manual, 80 stránky
Model KD-S10J	Uživatelský manuál JVC Model KD-S10J User Manual, 59 stránky
KD-G400	Uživatelský manuál JVC KD-G400 User Manual, 42 stránky
DIGITAL AUDIO KD-S550	Uživatelský manuál JVC DIGITAL AUDIO KD-S550 User Manual, 94 stránky
KD-AR600	Uživatelský manuál JVC KD-AR600 User Manual, 47 stránky
GET0114-001A	Uživatelský manuál JVC GET0114-001A User Manual, 42 stránky
0409DTSMDTJEIN	Uživatelský manuál JVC 0409DTSMDTJEIN User Manual, 4 stránky
1208MNMMDWJEIN	Uživatelský manuál JVC 1208MNMMDWJEIN User Manual, 4 stránky
KD-G505	Uživatelský manuál JVC KD-G505 User Manual, 42 stránky

Korg Triton Studio Uživatelský manuál Strana 112

Komentáře k této Příručce

JVC CS-V6 SERIES CS-V6936 manuály

Jvc CS-V6 SERIES CS-V6936 Uživatelský manuál (2 strany)

Tabulka s obsahem

Další produkty a příručky pro Reproduktory do auta JVC

Korg Triton Studio Uživatelský manuál Strana 112

Komentáře k této Příručce

Související produkty a manuály pro Vstupní zařízení Korg Triton Studio

JVC CS-V6 SERIES CS-V6936 manuály

Jvc CS-V6 SERIES CS-V6936 Uživatelský manuál (2 strany)

Tabulka s obsahem

Další produkty a příručky pro Reproduktory do auta JVC